Aller au contenu
Agents en ligne · Lun–Ven 8h00–16h30 HE
Siège Montréal · Amérique du Nord
Étalonnage à l'interne
Expédition rapide partout dans le monde
Vrai soutien technique
Depuis 1994

Anchor Straps: Types, Slings and How to Choose in Canada

Yellow web anchor strap with D-ring wrapped around a steel I-beam on a construction site

Yellow web anchor strap with D-ring wrapped around a steel I-beam on a construction site

Dans cet article

    An anchor strap is a portable anchorage connector: a length of webbing or cable that wraps around a structure and gives a worker's lanyard or self-retracting lifeline a tie-off point where no fixed anchor exists. Choosing one comes down to four things: what the strap wraps around, whether the work involves heat or sharp edges, the strength rating required in your province, and how the strap ends connect to the rest of the system. This guide covers the main styles and the 3M DBI-SALA, MSA, Miller and Peakworks connectors ERE Inc. supplies.

    In this guide


    What is an anchor strap?

    An anchor strap, also called an anchorage connector strap, tie-off adaptor or anchor sling, is a temporary tie-off point made by wrapping a strap or cable around a structural member such as an I-beam, a pipe, a column or a scaffold tube. It needs no drilling or welding. In Canada, anchorage connectors are covered by CSA Z259.15, which sets performance, design, testing and marking requirements. The CCOHS fall protection page explains where a fall protection plan is needed in the first place.

    The strap is only the top of the system. It works with a harness and a lanyard or lifeline, so if you are still selecting those parts, see our guides to the fall arrest harness, the shock-absorbing lanyard and the self-retracting lifeline.


    What are the types of anchor strap and sling?

    Anchor straps differ by material and by how the ends attach, and the right pairing depends on the structure and the hazards at the work location:

    • Web straps with D-rings: polyester webbing with a D-ring at one or both ends. The strap wraps the structure and the lanyard clips to the D-ring. They are light and quick to place, and suit beams, columns and scaffold members without sharp edges.
    • Choker-style straps: a web strap that passes through its own end loop and tightens around the structure. A scaffold choker is a short example for scaffolding or piping.
    • Pass-thru tie-off adaptors: a strap or cable with a loop or O-ring at each end; one end feeds through the other to form the wrap, which leaves a tie-off ring on the structure.
    • Cable anchor slings: steel cable with O-ring or eye ends. Cable resists abrasion and is the usual choice around rough steel, hot surfaces and welding work, where webbing can be cut or damaged.
    • Concrete anchor straps: a web loop with a D-ring that is cast into or looped around concrete, such as rebar or a cast-in anchor point on a slab edge.
    • Cross-arm straps: web straps sized to wrap an I-beam or utility cross-arm, with a D-ring that slips through a larger D-ring to form the wrap.

    Where the work is on a roof rather than a wrapped structure, a dedicated anchor may suit better: see our roof anchor guide, and for clamping to steel without a wrap, the beam anchor guide.


    How strong does an anchor strap have to be in Canada?

    It depends on the province, because there is no single national figure. 3M Canada's Anchorage Strength Requirements: Canada collects the regulation text by jurisdiction, and its general convention for fall arrest is 22.2 kN (5,000 lb) per attached worker for non-certified anchorages. A certified anchorage designed by a qualified person or engineer can instead be rated at two times the maximum arresting force.

    Jurisdiction Fall arrest anchor requirement (as quoted by 3M Canada)
    Alberta 16 kN per attached worker or two times the maximum arresting force
    British Columbia 22 kN (5,000 lb) or two times the maximum arrest force
    Ontario (construction) Temporary support: 8 kN static force, or 6 kN where a shock absorber is also used
    Quebec Breaking strength of at least 18 kN, or an engineered system, or a device certified to EN 795 or CAN/CSA Z259.15
    Saskatchewan, Northwest Territories Breaking strength of at least 22.2 kN

    These figures are summaries, and regulations are amended, so check the current text for the province where the work is. A strap's own rating is only half the check: the structure it wraps and the connection points must also take the load, and a qualified person should confirm that before use. Read the rating on the product data sheet rather than assuming it from the style.


    Which anchor straps does ERE supply?

    ERE Inc. supplies anchorage connectors from several makers, all listed for temporary use. Specifications below come from the product listings, so confirm ratings on the data sheet for your installation.

    The full range, including fixed and permanent anchorage connectors, is on the fall protection collection.


    How to choose an anchor strap

    1. Identify the structure. Beam, pipe, column, scaffold or concrete decide the strap style and length. Measure the largest member you will wrap.
    2. Check the hazards. Sharp edges, abrasion, heat or welding point to cable or a protected strap; clean, smooth members suit webbing.
    3. Check the rating. Compare the listed strength with the current figure for the province, and multiply for each worker attached.
    4. Match the end connections. The D-ring, O-ring or loop has to accept the snap hook or carabiner on the lanyard or lifeline, and the system's components must be rated for the same use.
    5. Confirm the structure. A qualified person should assess the member, its connections and what supports it.
    6. Inspect and plan the rescue. Check the strap for cuts, wear and damage before each use, and settle how a fallen worker is recovered before work starts.

    Not sure which strap fits your structure? Request a quote with the structure, the work to be done and the province, and we will match the connector, or call us in Montreal.


    Need help with anchor straps?

    ERE Inc. has been Canada's environmental and safety equipment specialist for 30+ years. Talk to a real specialist about your structures and your fall protection plan.

    → Request a Quote | 1-888-287-EREC | Browse Fall Protection | sales@ereinc.com

    Frequently Asked Questions

    What is the difference between an anchor strap and a tie-off adaptor?

    The terms overlap. Both wrap a structure to create a tie-off point. "Tie-off adaptor" usually describes a pass-thru design with a loop or ring at each end, while "anchor strap" or "anchorage connector strap" often refers to a web strap with a D-ring. Check the product listing for the exact style.

    Can you use an anchor strap around a sharp edge?

    Only if the manufacturer's instructions allow it. Webbing can be cut by sharp or abrasive edges, so cable slings or straps with wear pads are used around rough steel, and the edge has to be assessed as part of the fall protection plan.

    How much weight does an anchor strap support?

    It depends on the model and on the province. A common Canadian convention for fall arrest is 22.2 kN (5,000 lb) per attached worker for a non-certified anchorage, and provincial figures run from 16 kN in Alberta to 18 kN in Quebec. Read the rating on the product data sheet, and have the structure checked by a qualified person.

    Is an anchor strap reusable?

    Many are designed for repeated temporary use, but each must be inspected before every use and removed from service if it shows cuts, wear, heat damage or after arresting a fall, following the manufacturer's instructions.

    Related articles

    Lire en français : Sangle d'ancrage : types, élingues et choix au Canada