A beam anchor is a portable anchorage connector that clamps onto a steel I-beam or H-beam so a worker's lanyard or self-retracting lifeline has a tie-off point overhead. Choosing one comes down to four things: the flange width and thickness of the beam, whether the anchor must stay fixed or travel along the beam, the strength rating required in your province, and what the rest of the system connects to. This guide covers the three main styles and the 3M DBI-SALA beam anchors ERE Inc. supplies.
In this guide
- What is a beam anchor?
- What are the types of beam anchor?
- How strong does a beam anchor have to be in Canada?
- Which beam anchors does ERE supply?
- How to choose a beam anchor
- Frequently asked questions
What is a beam anchor?
A beam anchor is an anchorage connector that attaches to the flange of a structural steel beam and gives a personal fall protection system a secure tie-off point, without welding or drilling. The standard covering these devices in Canada is CSA Z259.15, which sets performance, design, testing and marking requirements for anchorage connectors. The CCOHS fall protection page explains where a fall protection plan is needed in the first place.
A beam anchor is only the top of the system. It works with a harness and a lanyard or lifeline, so if you are still selecting those parts, see our guides to the fall arrest harness and the self-retracting lifeline. For anchors on other structures, see the roof anchor guide.
What are the types of beam anchor?
Beam anchors fall into three styles, and the difference is whether the tie-off point stays in one place or moves with the worker:
- Fixed beam anchors: clamp to the flange and stay where they are put. They suit work in one spot, such as an inspection or repair at a single location on the beam.
- Sliding (adjustable) beam anchors: adjust to a range of flange widths and clamp to the beam. A sliding anchor is the general-purpose choice when the same anchor has to fit different beams across a site.
- Beam trolley anchors: roll along the bottom flange so the tie-off point follows the worker overhead. They suit travel along a beam, where re-attaching an anchor every few metres is slow and exposes the worker at each move.
For a worker moving over a longer run, a trolley on a beam is one option and a horizontal lifeline is another; a beam anchor can also serve as the end anchorage for a temporary horizontal lifeline, provided every part is rated for it.
How strong does a beam anchor have to be in Canada?
It depends on the province, because there is no single national figure. 3M Canada's Anchorage Strength Requirements: Canada collects the regulation text by jurisdiction, and its general convention for fall arrest is 22.2 kN (5,000 lb) per attached worker for non-certified anchorages. A certified anchorage designed by a qualified person or engineer can instead be rated at two times the maximum arresting force.
| Jurisdiction | Fall arrest anchor requirement (as quoted by 3M Canada) |
|---|---|
| Alberta | 16 kN per attached worker or two times the maximum arresting force |
| British Columbia | 22 kN (5,000 lb) or two times the maximum arrest force |
| Ontario (construction) | Temporary support: 8 kN static force, or 6 kN where a shock absorber is also used |
| Quebec | Breaking strength of at least 18 kN, or an engineered system, or a device certified to EN 795 or CAN/CSA Z259.15 |
| Saskatchewan, Northwest Territories | Breaking strength of at least 22.2 kN |
These figures are summaries, and regulations are amended, so check the current text for the province where the work is. A beam anchor's own rating is only half the check: the beam, its connections and the structure carrying it must also take the load, and a qualified person should confirm that before use.
Which beam anchors does ERE supply?
ERE Inc. supplies three 3M DBI-SALA beam anchors, all listed for temporary use on I-beams. Specifications below come from the product listings, so confirm ratings on the data sheet for your installation.
- 3M DBI-SALA Fixed Beam Anchors fit beam flanges up to 1 1/2 in. thick and 2 1/2 in. to 12 in. wide, install in seconds in any orientation and tighten with a built-in adjustment handle.
- 3M DBI-SALA Sliding Beam Anchor covers a variety of beam sizes with an integrated dual ratcheting system, replaceable wear pads and a 360-degree swiveling D-ring. The listing states 5,000 lb strength and up to 420 lb (189 kg) capacity.
- 3M DBI-SALA Beam Trolley Anchorage Connectors install overhead with no tools at the ends or midpoint of the beam and fit flat or tapered flanges 3 in. to 8 in. wide and up to 11/16 in. thick. Double-shielded wheel bearings and trolley guards keep it rolling.
Where a beam cannot take a clamp, other connectors can wrap it: the Miller cross-arm straps and the web tie-off adaptor are listed for temporary use. The full range is on the fall protection collection.
How to choose a beam anchor
- Measure the flange. Record width and thickness, and note whether the flange is flat or tapered.
- Pick the style. Fixed for one location, sliding for varied beams, trolley for travel along the beam.
- Check the rating. Compare the anchor's listed strength with the current figure for the province, and multiply for each worker attached.
- Confirm the beam and structure. A qualified person should assess the beam, its connections and what supports it.
- Match the connector and lifeline. The lanyard, SRL and connectors must be rated for the same use.
- Plan the rescue. Settle how a fallen worker is recovered before work starts, and inspect the anchor before each use.
Not sure which anchor fits your beam? Request a quote with the flange size and the work to be done, and we will match the anchor, or call us in Montreal.
Need help with beam anchors?
ERE Inc. has been Canada's environmental and safety equipment specialist for 30+ years. Talk to a real specialist about your beams and your fall protection plan.
→ Request a Quote | 1-888-287-EREC | Browse Fall Protection | sales@ereinc.com
Frequently Asked Questions
What is the difference between a beam anchor and a beam clamp?
In fall protection the two terms are often used for the same device: a connector that clamps onto a beam flange and provides a tie-off point. The word "beam clamp" is also used in general rigging and hardware for clamps that carry loads rather than workers, so for personal fall protection check that the device is listed as an anchorage connector.
What is a beam trolley used for?
A beam trolley rolls along the bottom flange of a beam so the tie-off point moves with the worker. It is used where a worker travels along a beam and re-attaching a fixed anchor at each step would be slow and exposed.
How much weight does a beam anchor support?
It depends on the model and on the province. A common Canadian convention for fall arrest is 22.2 kN (5,000 lb) per attached worker for a non-certified anchorage, and provincial figures run from 16 kN in Alberta to 18 kN in Quebec. Read the rating on the product data sheet, and have the beam checked by a qualified person.
Can a beam anchor go on any I-beam?
No. Each model has a flange width and thickness range, and the flange can be flat or tapered. An anchor used outside its stated range may not clamp securely, so measure the beam before you choose.
Related articles
- Roof anchor: types, strength and how to choose
- Horizontal lifeline: types, sag and how to choose
- Self-retracting lifeline: CSA classes and how to choose
Lire en français : Ancrage de poutre : types, résistance et choix au Canada