A bacon bomb is a weighted, closed metal sampler lowered on a chain into a storage tank and opened at a chosen depth, so it collects a spot sample from that depth only. Use one when you need a sample from a specific level of a tank, not a whole-column sample from a drum. ERE lists the Bacon Bomb Multi-Layer Samplers from The George Taylor Brass & Bronze Works in seven sampler lengths and two extension-rod options, and ships across Canada.
In this guide
- What is a bacon bomb sampler?
- How does a bacon bomb sampler work?
- At what depths do you take a sample?
- Bacon bomb, coliwasa or drum thief: which one?
- How do you take a sample with a bacon bomb?
- How do you keep a metal sampler safe in a tank?
- How do you choose a bacon bomb?
- Frequently asked questions
What is a bacon bomb sampler?
A bacon bomb is a bullet-shaped metal container with a stopper or plunger at one end, lowered on a line or chain to collect a liquid sample at a set depth. Gammon Technical Products describes the classic design, credited to chemical engineer Charles V. Bacon, as made of brass and bronze with nickel plating, and as conforming to ASTM D4057 (Gammon Bulletin 115). It is used on petroleum oils and jet fuels, solvents, chemical solutions, varnish, vegetable oils and other liquids held in tanks.
About 210 searches a month in Canada are for "bacon bomb" and 40 for "bacon bomb sampler". The product page for ERE's version notes use in petroleum refineries, chemical plants and fisheries, and lists sampler lengths from 9 to 17 inches plus a 12-inch extension rod and a 1, 2, 3 and 6-inch extension rod set.
How does a bacon bomb sampler work?
The sampler goes down closed, opens when you pull the stopper at the depth you want, fills, and is closed again before it comes up. In the bottom-sampler design Gammon describes, a plunger keeps the body shut until it strikes the tank bottom, which opens it; when raised, the plunger drops back and seals it so no liquid from a higher level mixes in. The same bulletin notes that attaching a cable to the top of the plunger lets the operator raise it at will to fill at any point above the bottom.
Extension rods, such as the 12-inch rod and the 1, 2, 3 and 6-inch rod set listed with ERE's samplers, are how you sample a set height above the tank floor, for example to catch water or sediment that settles at the bottom. Confirm the exact opening mechanism of the model you order with ERE before relying on it in a procedure.
At what depths do you take a sample from a tank?
Standard practice names four spot-sample positions: top, upper, middle and lower. Per the definitions in ASTM D4057 as quoted from API MPMS Chapter 8.1 by Hawkins, they sit at these points in the liquid:
| Spot sample | Where it is taken |
|---|---|
| Top sample | 15 cm (6 in.) below the liquid surface |
| Upper sample | Middle of the upper third of the contents (one-sixth of the depth below the surface) |
| Middle sample | Middle of the contents (one-half of the depth) |
| Lower sample | Middle of the lower third (five-sixths of the depth) |
The same chapter says spot samples can be taken to assess how much a property is stratified within a shore tank or marine vessel compartment. The standards themselves are published by ASTM International (D4057) and the American Petroleum Institute; use the current edition for your procedure.
Bacon bomb, coliwasa or drum thief: which one do you need?
Choose a bacon bomb for depth-specific samples in a tank, a coliwasa for a full-column sample of a drum, and a drum thief for a quick grab from a drum. The tools answer different questions, so the container usually decides.
| Tool | What it collects | Typical container |
|---|---|---|
| Bacon bomb | Spot sample at a chosen depth | Storage tank |
| Coliwasa | Full-depth, vertical column of the liquid | Drum |
| Drum thief | Grab sample from a drum | Drum |
| Sub-surface sampler | Sample at depth on a line | Tank, pond or lagoon |
See our guides to coliwasa samplers and sample thieves, or the full drum and tank liquid sampling guide. For depth sampling on a line without a bacon bomb, ERE also lists the 6000 stainless steel sub-surface samplers, the telescopic 7000 aluminum sub-surface samplers and the deep water sampler.
How do you take a sample with a bacon bomb?
- Pick the sample point. Decide top, upper, middle, lower or a height above the bottom, and measure the liquid depth first so the line can be marked.
- Clean and check the sampler. Rinse it, confirm the stopper seats and moves freely, and confirm the metal suits the liquid.
- Bond before you lower. Clamp the chain to a bare metal part of the tank, then lower the sampler. See the safety section below.
- Lower to the depth and open. Use depth marks on the line, then pull the stopper line to fill. Allow time for the sampler to fill.
- Close and raise. Release the line so the stopper reseats, then bring the sampler up without letting it knock the tank.
- Transfer and label. Fill a clean container, record depth, date and tank, and follow your lab's chain-of-custody rules.
How do you keep a metal sampler safe in a tank?
Bond the sampler to the tank through a conductive chain before it enters the liquid, and never use rope or cord. Gammon's guidance is to attach the clamp to a metal component of the tank first, clearing paint or rust that could break continuity, and then lower the sampler, because an unbonded object entering a tank can spark.
The Canadian Centre for Occupational Health and Safety (CCOHS) explains why: static charge builds up when fuels and solvents move in contact with other materials, and bonding with bare metal-to-metal connections prevents sparks. Check your site's hot-work and confined-space rules, and your SDS, before sampling.
How do you choose a bacon bomb?
Choose by length and by which depths you must reach. ERE's listing offers 9, 10, 11, 12, 15.5, 16 and 17-inch samplers. Match the sampler to the hatch or gauging opening you will use, add an extension rod if you need a fixed height above the bottom, and check that brass or bronze is compatible with the liquid; Gammon notes that liquids which attack nickel and bronze call for a protective coating.
Browse the full liquid sampling collection, or send us the tank, the liquid and the depths and we will match the sampler.
Frequently asked questions
What is a bacon bomb sampler used for?
It collects a liquid sample from a chosen depth in a tank. Typical liquids include petroleum oils, jet fuels, solvents, chemical solutions and varnish.
Can a bacon bomb sample the bottom of a tank?
Yes. In the bottom-sampler design, the stopper opens on contact with the tank bottom to pick up sediment or water, and extension rods let you sample a set height above it.
Does a bacon bomb meet ASTM D4057?
Gammon states its bacon bomb models conform to ASTM D4057, the standard practice for manual sampling of petroleum and petroleum products. Ask ERE to confirm the standard for the model you order.
Does ERE stock bacon bomb samplers?
The Bacon Bomb Multi-Layer Samplers are listed in our catalogue. Availability varies, so request a quote and we will confirm current stock and lead time.
Need a bacon bomb sampler for your tank?
ERE Inc. has supplied environmental sampling equipment from Montreal for 30+ years. Tell us the tank, the liquid and the sampling depths, and we will match the sampler.
→ Request a Quote | 1-888-287-EREC | Browse Liquid Sampling | sales@ereinc.com
Lire en français : Échantillonneur Bacon Bomb : fonctionnement et utilisation au Canada